MYK LATICRETE LATAFIX 305 (20KG) FLOOR AND WALL THINSET ADHESIVE

About MYK LATICRETE LATAFIX 305 (20KG) FLOOR AND WALL THINSET ADHESIVE

 91 000 74051 LATAFIX 305 FLOOR AND WALL THIN-SET ADHESIVE
A factory made bagged cementitious powder, containing Portland cement and silica sand, it can be mixed with water for installing small and medium size ceramic floor tiles in interior areas using the thinset method of installation

Certification:
ANSI : Meets ANSI A 118.1
ISI: TYPE 1 ADHESIVE
EN 12004/ISO 13007:CIT
VOC: Nil

Advantages:
Ideal for fixing ceramic tiles on floor
Meets ANSI A 118.1
Economy Grade
Smooth & Creamy

Substrate:
The surface to be covered with Ceramic tile shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in:
Walls 3mm in 2.5m
Floors 1.5mm in 1.0m

Surface Preparation:
a) If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile.
b) Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc.
c) Dampen the wall before application of thin set adhesive
d) Clean the back of tile for any dust or coating.

Mixing:
The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm).
Pour potable clean water in a clean container and then add the powder Latafix 305 and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need.
Proportion: Approximately 1 bag of Latafix 305 with 5-6 ltrs of water. Adjust quantity of liquid to obtain proper consistency.

Installation:
Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered. Additional mortar is then applied with the notched edge of the trowel.
When installing large tiles, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel.
a) Thin Tiles upto size 300 X 300 mm (1X1), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm
b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm
c) Large Porcelain Tiles upto 600 X 600 mm (2X2) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm
The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.

Premium Tile Adhesion Simplified

Designed for versatility, MYK LATICRETE LATAFIX 305 ensures durable bonding of a variety of tiles and stones. Its single-component, polymer-modified formula makes mixing and application straightforward, catering to both floor and wall surfaces. With consistent performance and compliance to national and international standards, it is an excellent choice for professional installations.


Efficient Mixing and Application

LATAFIX 305 requires only water for preparation-just mix 4.5 to 5.5 liters of water per 20 kg bag for optimal consistency. The pot life is approximately 4 hours at 27C, offering ample working time. The adhesive provides an open time of 20 minutes and adjustability of 10-15 minutes, helping achieve precise tile placement.


Long-lasting Results and Strength

Exhibiting a shear adhesion strength greater than 1.0 N/mm2 and compressive strength above 10 N/mm2 after 28 days, LATAFIX 305 delivers reliable, long-term performance. With a coverage rate of 3-4 kg/m2, it is economical and efficient for a range of tile installation projects. Its 12-month shelf life ensures product availability when needed.