MYK LATICRETE 305 ADHESIVE

About MYK LATICRETE 305 ADHESIVE

 91 000 74051 LATAFIX 305 FLOOR AND WALL THIN-SET ADHESIVE
A factory made bagged cementitious powder, containing Portland cement and silica sand, it can be mixed with water for installing small and medium size ceramic floor tiles in interior areas using the thinset method of installation

Certification:
ANSI : Meets ANSI A 118.1
ISI: TYPE 1 ADHESIVE
EN 12004/ISO 13007:CIT
VOC: Nil

Advantages:
Ideal for fixing ceramic tiles on floor
Meets ANSI A 118.1
Economy Grade
Smooth & Creamy

Substrate:
The surface to be covered with Ceramic tile shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in:
Walls 3mm in 2.5m
Floors 1.5mm in 1.0m

Surface Preparation:
a) If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile.
b) Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc.
c) Dampen the wall before application of thin set adhesive
d) Clean the back of tile for any dust or coating.

Mixing:
The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm).
Pour potable clean water in a clean container and then add the powder Latafix 305 and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need.
Proportion: Approximately 1 bag of Latafix 305 with 5-6 ltrs of water. Adjust quantity of liquid to obtain proper consistency.

Installation:
Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered. Additional mortar is then applied with the notched edge of the trowel.
When installing large tiles, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel.
a) Thin Tiles upto size 300 X 300 mm (1X1), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm
b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm
c) Large Porcelain Tiles upto 600 X 600 mm (2X2) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm
The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.

Superior Polymer-Modified Adhesive

MYK LATICRETE 305 is engineered with advanced polymers that enhance adhesion, flexibility, and durability. This makes it ideal for securely fixing ceramic, vitrified, and natural stone tiles on both floors and walls. Its high bond strength not only helps achieve a long-lasting installation but also reduces the risk of tile detachments and surface failures.


User-Friendly Application Process

The adhesive is supplied as a ready-to-mix powder, simplifying the preparation process. Just combine 3 parts powder with 1 part water by volume to obtain a smooth, workable paste. With a pot life of around 2 hours and an open time of 20 minutes, applicators have ample time to position tiles accurately. Full curing occurs in 14 days, but light traffic can be allowed after 24 hours.


Reliable Performance and Coverage

With excellent compressive strength (>10 MPa at 28 days) and efficient coverage of 3-4 kg per m2, MYK LATICRETE 305 delivers consistent performance across diverse substrates. Its stable grey or white powder form ensures versatility for different aesthetic needs while maintaining an odorless and safe work environment.